The floor plan checklist: what a drawing needs before anyone can quote it

A drawing can be accurate and still be unquotable. The walls are in the right place, the furniture fits, the client likes it — and the contractor comes back with a range so wide that it is not a price, it is a warning. Nothing is missing from the design; several things are missing from the sheet. This is the checklist for the second problem. Ten items that a plan has to carry before another trade can put a number against it, what each one is used for, and the specific way hand-drawn plans usually leave it out. It is not a guide to drawing, and it is not a code summary: the code sets a minimum for safety, and a quote needs considerably more than the minimum — quantities, positions and materials that the code never asks about.

HomeDesignly editorial team10 min read

The floor plan checklist: what a drawing needs before anyone can quote it

Key takeaways

  • A price is a quantity times a rate, so the drawing has to make quantities computable: overall size, room sizes, and every opening[2, 3].
  • Written dimensions govern; a plan that has to be scaled to be understood is already a weak document[3, 4].
  • Code minimums are a floor, not a brief: a habitable room can be 70 sq ft (6.5 m²) and a ceiling 7 ft (2134 mm) and still be impossible to quote from[1].
  • Every trade adds its own missing layer — cabinets need elevations, electricians need existing supplies, engineers need wall types[5].
  • Nothing on this list replaces a site visit: contract documents assume field measurements of existing conditions, and so should a quote[2].
On this page

Why a good drawing still cannot be priced

A contractor prices four things: quantities, labour, risk and margin. The drawing only supplies the first, and only if it is dimensioned. From a set of room sizes and openings a joiner can count metres of skirting, a tiler can count square metres of floor, an electrician can count points. From a plan without dimensions, the same trades can only guess — and a guess is priced high, because the person guessing carries the risk.

That is why the drawings that get sharp quotes look almost boring. Overall dimensions around the outside, a dimension string for every room, openings with sizes and swing, wall thicknesses, a height, and a note that says what the drawing is. None of that is design. All of it is the difference between a price and a range.

The plan also has to be readable as a document rather than a picture. A drawing that carries written dimensions takes precedence over anything scaled off the sheet[3], and a permit set says so in its own general notes — dimensions govern, do not scale the drawing[2]. A client's sketch with no numbers has neither: it can be scaled and it can be wrong, and there is nothing on the sheet to say which.

The ten-item checklist

Each row below is something a trade will look for and, if it is missing, either ask about or price defensively. The third column is the failure mode that shows up most often in plans drawn by hand or by a designer who has not priced work.

What a plan needs before it can be quoted, why each item matters, and how drawings usually leave it out[1, 2, 3, 4, 5]

ItemWhy a quote needs itHow hand-drawn plans usually leave it out
Overall dimensions and the outlineSets the envelope: every trade prices against the total footprint first, and a missing overall dimension sends them back to the start[2]One overall dimension that stops at the first projection; no width across the widest point; the outline left open at a doorway
Clear size of every roomFloor, skirting, tiles and paint are all computed from room areas, so each room needs its own dimensions[2]Rooms drawn but never dimensioned; dimensions taken to wall centres instead of finished faces
Door and window openings, with swingOpenings are ordered items and each one interrupts a wall run; the swing decides what can be placed beside it[3]Openings drawn as gaps with no size; no hinge side; a door swing that lands on a radiator
Wall thickness, partition or load-bearingThickness decides whether a run fits at all, and whether a wall can move is a structural question, not a drawing preference[3]Single-line walls throughout; no distinction between a stud partition and a structural wall
Ceiling heightCeilings, lights, extractors and full-height cabinets are all priced against a height, and the code sets a minimum for habitable space[1]No height anywhere on the sheet, and no section to find it in
Fixed services: water, power, gas, heatingEvery move of a sink, hob, radiator or socket is a separate plumbing or electrical line itemAppliances drawn as boxes, with nothing to say which wall carries water, waste or power
Stairs and treadsA stair is priced by flight, and the rise and going have to fit the floor-to-floor height; the code fixes minimums[1]A ladder of lines with no direction arrow, no width and no rise
Scale, or a clear not-to-scale noteA scale lets the reader check a dimension; a plan marked not to scale forces them to price from the written numbers only[4]No scale in the title block, or a print resized to fit the paper so the stated scale no longer holds[4]
Existing versus new workDemolition, making good and temporary protection are separate line items with their own riskNew walls drawn in the same line weight as existing ones; no demolition plan at all
Title block: project, level, date, revisionA price is given against a revision, and a quote against the wrong one becomes a variation[5]No date, no revision, no sheet number — three sets in circulation and no way to tell them apart
The code references are minimums and they vary by jurisdiction[1]; nothing in this table is a code requirement in itself, because no code requires a plan to be quotable. The right-hand column describes common practice, not a survey: how a particular drawing fails is a judgement about that drawing.

What each trade adds on top

One plan rarely serves everyone. The same room needs a different second sheet for a cabinet maker, an electrician and a structural engineer, and the difference is not cosmetic: it is the information each of them needs to buy or build without a site visit of their own.

One habit makes all four columns easier: send the drawing with the question attached. A line in the covering message that says what is being quoted — supply and fit, labour only, or a budget range — changes what the contractor needs from the sheet, and it costs nothing to write. The drawing then answers a specific question instead of every possible one.

The same layout, four readers: what each one needs beyond the plan[2, 5]

WhoStill needsCannot price without it
Main contractorThe ten-item checklist, plus a site visit and the existing-services locationsDemolition, protection, access, making good, and the risk that comes with not knowing what is behind a wall[2]
Cabinet makerA dimensioned elevation of every run: worktop height, appliance sizes, ceiling height, service voidsDoor and drawer widths, filler panels, and whether the tall unit fits under the ceiling[1]
Electrician and plumberPositions of the existing supply, consumer unit, stopcock and drains, plus the new pointsCable and pipe runs, and whether the floor or ceiling can be opened without structural work
Structural engineerWall types, spans and a clear statement of which walls are proposed for removalBeam sizes, bearings and padstones — and therefore whether the opening is possible at all[3]
The list is a starting point, not a standard: what a trade asks for also depends on the region, the contract type and how much risk they are willing to carry. Ask the person quoting before the drawing is finished, not after.

The five that are always missing

Of the ten items, five go missing so reliably that they are worth checking before anything else.

**Ceiling height.** A plan cannot show it, and a section often does not exist on a small job. The code sets 7 ft (2134 mm) for habitable space and hallways, and 6 ft 8 inches (2032 mm) for bathrooms, toilet rooms and laundry rooms[1] — which tells you the floor, not the room. A kitchen with a low ceiling and a run of full-height units is a different quote from the same kitchen with headroom above them, and the drawing has to say which one it is.

**Wall thickness.** Two lines close together and two lines far apart are the difference between a thin partition and a structural wall, and the difference between a run that fits and one that does not[3]. The drafting convention is that hatches say what a wall is made of[3]; if the walls are not hatched, the thickness is the only clue left, and single-line walls remove it.

**Services.** Water, waste, gas and power are the items that turn a layout change into a cost. A sink moved across a room is a drain run; a hob moved to an island is a gas run or a heavier cable, depending on the answer nobody has written down. The plan does not need a plumbing design, but it does need to show what is already there.

**Stairs.** A stair is a measured object with code minimums: in this state's edition, a riser of not more than 8¼ inches (209 mm), a tread of not less than 9 inches (229 mm), and a clear width of not less than 36 inches (914 mm)[1]. Other editions and other states use different figures, which is exactly why the drawing should carry the rise and going it was designed to, rather than leave the joiner to infer them[1].

**Scale and revision.** A plan without a scale can still be priced from its dimensions, but it cannot be checked[4]. A plan without a date or a revision cannot be quoted at all, because the quote will be against whichever copy the contractor happens to open[5].

Before you send it

The self-check takes a few minutes and catches most of the list. Put a dimension on every room, in both directions. Close the outline. Size every opening and draw its swing. Give every wall a thickness, and hatch the ones that are structural. Write the ceiling height on the plan, not just in your head. Mark what is existing and what is new. Add a title block with the project, the level, the date and a revision, and say either the scale or that the drawing is not to scale. Then read it as if you were the person quoting: is there anything you would have to ask?

Two notes on honesty. First, the code is a floor: a habitable room may be as small as 70 sq ft (6.5 m²) with 7 ft (2134 mm) in one direction[1], and a hallway 3 ft (914 mm) wide[1], and a dwelling can be built exactly to those numbers — but a quote built on them is a quote for the smallest legal version of the room, not the one the client has been shown. Second, no drawing replaces the site: contract documents require field measurements of existing conditions before work is priced or started[2], and the drawing is the record of what was measured, not a substitute for measuring.

If the plan needs rebuilding before it can be sent, the floor plan creator opens a template with the scale already set, so the dimensions and the drawing stay one object. Two companion pieces in this series are worth reading beside this checklist: how to read a floor plan for the conventions on the sheet, and standard room dimensions for the numbers a room needs before it can hold what the client wants.

Produce a plan that can be priced

Generate the layout at a real size, with walls, openings and room dimensions already on it, then run the ten-item check before the drawing goes out. It is quicker to add a dimension now than to answer the same question three times next week.

AI floor plan generator: house plans in minutes
AI floor plan generator: house plans in minutes (Before)
BeforeAfter
AI preview: design concepts rendered with AI.
Open the floor plan generator

Frequently asked questions

Is a hand-drawn plan enough to get a quote?

It can be, if it carries the ten items: overall and room dimensions, opening sizes and swings, wall thickness, ceiling height, existing services, stairs, a scale or a not-to-scale note, existing versus new, and a dated title block. What kills a hand-drawn plan is not the drawing style, it is a missing dimension — the contractor then prices the uncertainty, and the uncertainty is expensive[2, 3].

Do I need a scale on a plan, or are dimensions enough?

Dimensions are what govern: written dimensions take precedence over anything scaled off the sheet, and a print that has been resized is no longer to scale[3, 4]. A scale is still worth stating, because it lets the reader check the drawing and it tells them the sheet was drawn rather than sketched[4].

The contractor says they will measure on site anyway. Is the drawing still needed?

Yes. Site measurement is how the contractor checks the drawing, not how they price it — contract documents require field measurements of existing conditions, and they still say dimensions govern and drawings are not to be scaled[2]. A quote has to be prepared from quantities, and quantities come from the drawing; measuring on site confirms them later.

Sources

Numbers in brackets in the text point to these sources.

  1. 1.New York State Department of State, Division of Building Standards and Codes, 2020 Residential Code of New York State (R304 room area, R305.1 ceiling height, R311.2 egress door, R311.6 hallways, R311.7 stairs), accessed November 5, 2026.
  2. 2.City of Austin, Building permit plan set, general notes (dimensions govern, field measurements), accessed November 5, 2026.
  3. 3.Skills/Compétences Canada, SCNC 2019 – Drawing Standards, 52 – Architectural Technology & Design (Secondary), Appendix 1: Industry Drafting Standards, accessed November 5, 2026.
  4. 4.U.S. Fire Administration (FEMA), Using Engineer and Architect Scales, accessed November 5, 2026.
  5. 5.BOMA Oakland/East Bay, Reading Construction Plans – Property Manager Training (title block and drawing index), accessed November 5, 2026.